詳解安全滑觸線常見故障處理方法-發(fā)昊滑觸線
更新時間：2021-01-04 點擊次數：2177次一、滑觸線斷電
A sliding contact line power,
主要原因：電刷在導管中爬坡；電刷磨損嚴重，無法觸及導體；導體接頭不平整；單集電器使用；導軌接頭松脫。
The main reason: brush in the conduit climbing; brush wear serious, can not touch the conductor; the conductor joint roughness; single collector; rail joint loosening.
處理方法：檢測集電器是否磨損嚴重，更換集電器；更換電刷；重新調整連接節(jié)點；采用雙刷集電器；重新調整擰緊連接螺釘。
Treatment methods: detection of collector is badly worn, replace the collector; Replacement Brush; re adjust the connection; with double brush collector; re adjust, tighten the screw connection.
二、導軌變形，集電器運動受阻
Two, rail deformation, collector movement blocked
主要原因：環(huán)境溫度過高；提掛架間距大或松脫。
The main reason: the high ambient temperature; lifting rack spacing or loose.
處理方法：局部采用隔熱板，室外加遮陽板；增加滑觸線提掛架數量，矯正導管，并擰緊螺釘。
Processing method: partial use of insulation board, outdoor and visor; increase the sliding contact wire rack number provided, correct catheter, and tighten the screws.
三、工作時滑觸線晃動大
Three, work of sliding contact line shaking big
主要原因：撥叉無法吸收傳動誤差；導軌正線直線度差；提掛架松動。
The main reason: fork cannot absorb transmission error; rail line straightness deviation; lifting rack loose.
處理方法：修正牽引器，使之能自由吸收傳動誤差；調整導軌直線度；擰緊提掛架螺釘。
Treatment methods: fixed traction device, which can free free absorption, transmission error; the adjusting guide rail straightness; tighten screws lifting rack.
四、電刷磨損快
Four, brush wear quickly
主要原因：接頭不平整；載流量過大；彈簧壓力大。
The main reason: joint roughness; carrying capacity is too large; the spring pressure.
處理方法：按要求重新連接導軌；增加集電器數量；更換、修正彈簧壓力。
Processing method: according to the requirement of re connected with the guide rail; increase the collector number; replacement, correction spring pressure.
五、電刷側面擦傷
Five, brush side abrasion
主要原因：電刷磨損，滑觸線集電器定為不正；牽引器的撥叉?zhèn)攘鬟f過大。
The main reason: brush wear, sliding touch line collector for it; the shifting fork side force of the tractor transmission is too large.
處理方法：更換、修正彈簧壓力；更換牽引撥叉或修正牽引器撥叉。
Processing method: replacement, correction spring pressure; replace the traction fork or modified tractor fork.
六、導軌內有火花
Six, rail spark
主要原因：電刷表面與導軌接觸不良。
The main reason: brush the surface in contact with the rail side.
處理方法：檢測導軌接頭，適當磨合電刷保證60%接觸面積。
Treatment methods: detecting the rail joint, appropriate running in brush to ensure 60% contact area.
七、滑觸線集電器行走有較大異響
Seven, the sliding contact line collector walking has large abnormal sound
主要原因：電流過大；接頭不平整。
The main reason: the current is too large; joint roughness.
處理方法：增加集電器數量；重新安裝導軌連接。
Treatment methods: increase the collector number; re install rail connection.
八、滑觸線集電器外殼擦傷
Eight, the sliding contact line collector casing abrasion
主要原因：導軌變形；集電器定為欠佳。
The main reason: rail deformation; collector for the poor.
處理方法：按故障2處理，增加定型夾；調整集電器。
Processing method: according to the fault treatment increased 2, shaping clamp; adjust the collector.
